Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
Listed here down the page you'll find lots of decent expertise relating to Installing A Bathtub.
Mounting a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a reasonably hard task. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open up a wall to remove the old tub and also position the brand-new bath tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. See to it you have qualified yourself for the task as well as are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bath tub in your bathroom if you have actually already purchased a brand-new tub and do not require to alter the plan of your previous water supply pipes.
Your devices and also product checklist must comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to avoid pressure on the tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipelines have been gotten rid of, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, put the bath tub in the required position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile tap port to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bathtub as well as also inspect the overflow outlet and the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the supplier's instruction manual. Tiling and securing around the bath tub should wait until the bathtub has been used at least once as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washers are in location in between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous kind should be linked to the tap finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, leading to difficulties with moisture and also possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are offered in tubes as well as cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water prior to sealing, to allow for the movement experienced when the tub is in usage. The sealant can crack fairly very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the market. It is advisable to fit the floor tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Try to leave a short review directly below. We will be pleased to listen to your suggestions about this blog. In hopes to see you back again in the near future. Make sure you take a moment to promote this article if you appreciated it. I thank you for reading our article about How to Install a Bathtub.
Facing a flood? Call us! Report this page